Balaji Gypsum Private Limited

• Gyproc Pro-Fill® is an Air-Drying jointing compound used for
  plasterboard finishing at vertical & horizontal joints. It is also used for filling the
  uneven gaps, small cut-outs and finishing of the internal and external corner joints.

Selecting the correct product for an application can save you time and money while jointing plasterboards.

• For filling joints and bedding tapes, a product which 'fills' the gap and dries quickly is required, so that further processes can be done immediately. Pro-Fill® is recommended for its quick-setting nature
• Pro-Fill® can be used for the second coat too, depending on the finish desired
• An air-drying product is required for the finishing coat. Use Pro-Fill® or Pro-Top® Ready Mix Jointing Compound All Purpose for an excellent finish of the joint
• Pro-Fill® is recommended for repairing joints and treating drilled holes for utilities
• Gyproc Joint Paper Tape is recommended for the best crack-resistance performance and fire-rated partitions and ceilings
• Gyproc Drywall Joint Tape (Fibre Tape) is recommended for quick jointing of plasterboards

• First Coat

  • Using an applicator / Trowel, fill the recess formed by the edges of the sheets with Gyproc Pro-Fill®.
  • Centre the paper tape along the joint and using a Taping knife / Trowel press the tape down into the Pro-Fill® ensuring no air bubble remain behind the tape.
  • Immediately apply a thin coat of Pro-Fill® over the surface of the tape (100-150 mm wide).
  • Allow it to dry

  • Second Coat

    • Apply a second coat of Gyproc Pro-Fill® with an Applicator / Trowel.
    • Ensure that this coat extends outside the area of the first coat (200-250 mm wide).
    • Allow to thoroughly dry and scrape back any build-up of compound along the joint.

    • Third Coat

      • Apply a finishing coat of Gyproc Pro-Fill® with an Applicator / Trowel.
      • Joint edges should be feathered at least 50 mm beyond the edges of the previous coat
      • Allow to dry. Lightly sand in the same direction as the joint using finer sandpaper.

• Gyproc Easi-Fill®90 is gypsum based powdered jointing compound with a setting time of 90 to 120 minutes.
  Gyproc Easi-Fill®90 is designed for Quick Jointing & Finishing of gypsum Boards.

• First Coat

  • Using an applicator / Trowel, fill the recess formed by the edges of the sheets with Gyproc Easi-Fill®90.
  • Centre the Gyproc Paper Tape along the joint and using a Taping knife / Trowel press the tape down into the Easi-Fill®90 ensuring no air bubble remain behind the tape.
  • Immediately apply a thin coat of Easi-Fill®90 over the surface of the tape (100-150 mm wide).
  • Allow it to dry

  • Second Coat

    • Apply a second coat of Gyproc Easi-Fill®90 with an Applicator / Trowel.
    • Ensure that this coat extends outside the area of the first coat (200-250 mm wide).
    • Allow to thoroughly dry and scrape back any build-up of compound along the joint.

    • Third Coat

      • Apply a finishing coat of Gyproc Easi-Fill®90 with an Applicator / Trowel
      • Joint edges should be feathered at least 50 mm beyond the edges of the previous coat.
      • Allow to dry. Lightly sand in the same direction as the joint using finer sandpaper.

      • Selecting the correct product for an application can save you time and money while jointing plasterboards.

        • For filling joints and bedding tapes, a product which 'fills' the gap and dries quickly is required, so that further processes can be done immediately. Easi-Fill®90 is recommended for its quick-setting nature
        • Easi-Fill®90 can be used for the second coat too, depending on the finish desired
        • An air-drying product is required for the finishing coat. Use Pro-Fill® or Pro-Top® Ready Mix Jointing Compound All Purpose for an excellent finish of the joint
        • Easi-Fill®90 is recommended for repairing joints and treating drilled holes for utilities
        • Gyproc Joint Paper Tape is recommended for the best crack-resistance performance and fire-rated partitions and ceilings
        • Gyproc Drywall Joint Tape (Fibre Tape) is recommended for quick jointing of plasterboards

Gyproc Pro-top® is a Polymer-based ready-to-work air-drying product designed for all stages of jointing & Finishing and conforms to ASTM C476/C475M:2007.

Benefits

Ready-To-Work Product –
Water Not Needed

Air Drying

Saves
Time

Excellent
Workability

Smooth High-Quality
Finish

Zero/ Minimum Wastage
And Reuse Of Bucket

Application

Gyproc Pro-Top Ready-Mix is an Air-Drying ready to use jointing
compound for plasterboard finishing at vertical & horizontal joints. It is also used for
filling the uneven gaps, small cut-outs and finishing of the internal and external corner joints.

Weight: 30 Kg,20 Kg & 5 Kg pail

Process of Jointing & Finishing

First Coat

• Using an applicator / Trowel, fill the recess formed by the edges of the sheets with Gyproc Pro-Top®.
• Centre the paper tape along the joint and using a Taping knife / Trowel press the tape down into the Gyproc Pro-Top® ensuring no air bubble remain behind the tape.
• Immediately apply a thin coat of Gyproc Pro-Top® over the surface of the tape (100-150 mm wide).
• Allow it to dry

Second Coat

• Apply a second coat of Gyproc Pro-Top® with an Applicator / Trowel.
• Ensure that this coat extends outside the area of the first coat (200-250 mm wide).
• Allow to thoroughly dry and scrape back any build-up of compound along the joint.

Third Coat

• Apply a finishing coat of Gyproc Pro-Top® with an Applicator / Trowel.
• Joint edges should be feathered at least 50 mm beyond the edges of the previous coat.
• Allow to dry. Lightly sand in the same direction as the joint using finer sandpaper.

Selecting the correct product for an application can save you time and money while jointing plasterboards.

• For filling joints and bedding tapes, a product which 'fills' the gap and dries quickly is required, so that further processes can be done immediately. Easi-Fill® is recommended for its quick-setting nature
• Easi-Fill® can be used for the second coat too, depending on the finish desired
• An air-drying product is required for the finishing coat. Use Pro-Fill® or Pro-Top® Ready Mix Jointing Compound All Purpose for an excellent finish of the joint
• Easi-Fill® is recommended for repairing joints and treating drilled holes for utilities
• Gyproc Joint Paper Tape is recommended for the best crack-resistance performance and fire-rated partitions and ceilings
• Gyproc Drywall Joint Tape (Fibre Tape) is recommended for quick jointing of plasterboards